Frigidaire FHDP5033W1 Dehumidifier Manual

The Frigidaire FHDP5033W1 is a high-capacity dehumidifier designed for residential use, capable of removing up to 50 pints of moisture per day. It features electronic controls with a digital display, a continuous drain option, a washable filter, an auto-restart function, and a built-in humidistat for precise humidity control. Below are key sections for safety, features, installation, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Electronic control panel with digital display, Water tank with full indicator, Continuous drain port, Washable air filter, Casters for mobility, Auto-defrost function.

Installation & Placement

Unpack and inspect contents. Ensure all parts are present and undamaged.

1. Choose Location: Place on a level, hard floor in the center of the room for optimal air circulation. Keep at least 12 inches away from walls and furniture.
2. Check Clearance: Ensure the air intake (rear) and discharge (front) grilles are unobstructed.
3. Setup for Drainage: Decide between using the water bucket or continuous drain hose. For hose use, connect a standard garden hose (not included) to the drain port at the back.
4. Power Connection: Plug the unit directly into a grounded 115V AC, 60Hz outlet. Do not use an extension cord.

WARNING! Do not install in areas with temperatures below 41°F (5°C) or above 95°F (35°C). Never place on soft surfaces like carpet where air vents could be blocked.

First-Time Setup

Power on the dehumidifier; the digital display will illuminate.

1. Initial Dry-Out: Allow the unit to run for 24 hours in a new space to remove construction moisture.
2. Set Humidity Level: Press the HUMIDITY button to set your desired level (recommended 45-50% for comfort).
3. Select Fan Speed: Choose between HIGH (faster dehumidification) or LOW (quieter operation).
4. Timer Setup (Optional): Use the TIMER button to program automatic start/stop times.
5. Check Drainage: If using the bucket, ensure it is correctly seated. If using the hose, verify it is securely attached and routed to a floor drain or sink.

CAUTION! Always handle the water bucket with care to avoid spills. Empty the bucket before it becomes full to prevent auto-shutoff and potential overflow.

Specifications

• Model: FHDP5033W1
• Dehumidification Capacity: 50 Pints per day (at 60°F, 60% RH)
• Power Supply: 115 Volts, 60 Hz, 5.0 Amps
• Water Tank Capacity: 1.6 Gallons (6.0 Liters)
• Operating Conditions: 41°F to 95°F (5°C to 35°C)
• Air Flow: High Efficiency Cross-flow fan
• Refrigerant: R-410A
• Product Dimensions (HxWxD): 19.6" x 15.4" x 11.2"
• Weight: 40.8 lbs
• Certifications: ETL Listed, EPA 608 Certified

Controls and Settings

Access all functions via the electronic control panel on top of the unit.

Control Panel: POWER, HUMIDITY (+/-), FAN SPEED (HIGH/LOW), TIMER (1-24 Hr), FILTER ALERT Reset, CONTROL LOCK.

Digital Display: Shows current room humidity, set humidity level, fan speed, timer status, filter alert, and bucket full indicator.

Humidity Control: Adjust set point between 35% and 85% RH. The compressor will cycle on/off to maintain this level.

Fan Speed: HIGH for maximum moisture removal, LOW for quiet nighttime operation.

Timer: Set delay start (1-24 hours) or auto shut-off. The unit will remember the setting after a power outage if Auto Restart is enabled.

Operation Modes

Normal Dehumidification: Unit runs until desired humidity is reached, then fan runs intermittently to monitor conditions.

Continuous Mode: Press and hold HUMIDITY button for 3 seconds to run continuously regardless of humidity level (for very damp spaces).

Auto Defrost Mode: Activates automatically when coil temperature drops too low. The compressor will pause, and the fan may continue until frost clears.

1. Select desired mode using control panel.
2. Monitor the water bucket or ensure continuous drain hose is flowing.
3. Adjust settings as needed for seasonal changes (e.g., lower humidity setting in summer).

Tip: For maximum efficiency, keep doors and windows closed in the room where the dehumidifier is operating.

Maintenance & Cleaning

Unplug the unit before performing any maintenance.

1. Empty Water Bucket: Remove bucket, empty water, and replace securely. Clean bucket monthly with mild detergent.
2. Clean Air Filter: Remove the washable filter every 2 weeks or when the FILTER alert lights. Rinse under lukewarm water, let air dry completely before reinstalling. Press FILTER RESET button.
3. Clean Exterior: Wipe cabinet with a soft, damp cloth. Do not use harsh chemicals or abrasives.
4. End-of-Season Cleaning: Run the unit in Fan Only mode for a few hours to dry internal components before storage. Ensure the bucket and all parts are completely dry.

CAUTION! Never immerse the unit in water. Do not operate without the air filter installed, as this can damage the coil.

Storage Instructions

If not using the dehumidifier for an extended period:

1. Unplug the unit from the outlet.
2. Empty and thoroughly dry the water bucket.
3. Clean the air filter and let it dry.
4. Coil the power cord and secure it in the storage wrap.
5. Store the unit upright in a cool, dry place. Cover with a cloth to prevent dust accumulation.
6. Do not store on its side or upside down.

WARNING! Proper storage prevents mold growth and component damage. Ensure the unit is completely dry inside and out.

Regulatory Information

This appliance complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. This product contains refrigerant. Disposal must comply with federal and local regulations. For service or warranty information, contact Frigidaire at 1-800-374-4432 or visit www.frigidaire.com.

Troubleshooting

Reset: Unplug the unit for 5 minutes to perform a full system reset.

Service: 1-800-374-4432; www.frigidaire.com