Frigidaire FDM30R1ENG12 Dehumidifier Manual

The Frigidaire FDM30R1ENG12 is a 30-pint dehumidifier designed for residential use, featuring electronic controls, auto-restart, continuous drain option, washable filter, and low-temperature operation capability. It helps control humidity levels in rooms up to a specified area, reducing moisture, mold, and mildew. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Electronic control panel, built-in humidistat, removable water bucket with full-bucket indicator, continuous drain hose connection, washable air filter, and caster wheels for mobility.

Installation & Placement

Unpack and inspect contents. Place on a level, stable floor.

1. Choose location: Place in center of room or area with high humidity, away from walls and furniture for proper airflow.
2. Ensure clearance: At least 12-18 inches of space on all sides, especially intake and exhaust grilles.
3. Check power: Use a dedicated 115V AC, 60Hz outlet. Do not use extension cords.
4. Install drain hose (optional): For continuous drainage, attach standard garden hose to drain outlet and route to floor drain or suitable container.

WARNING! Do not place in tight enclosures or near heat sources. Ensure the unit is upright before operating.

First-Time Setup

Plug into power outlet; unit will beep and display will light up.

1. Install water bucket: Ensure bucket is correctly seated and locked in place.
2. Set humidity level: Press HUMIDITY button to set desired RH% (typically 45-50% for comfort).
3. Select fan speed: Choose HIGH or LOW fan setting based on dehumidification need and noise preference.
4. Set timer (optional): Use TIMER button to program automatic start/stop times.
5. For continuous drain: Attach hose and ensure downward slope for proper drainage.

CAUTION! Handle with care; unit contains refrigerant. Do not tilt or invert after setup.

Specifications

• Model: FDM30R1ENG12
• Dehumidification: 30 pints per day (at 80°F, 60% RH)
• Power Supply: 115V AC, 60Hz, 3.5 Amps
• Operating Conditions: 41°F to 90°F
• Water Bucket Capacity: Approximately 1.8 gallons
• Air Flow: Adjustable fan speeds (High/Low)
• Noise Level: ≤ 52 dB on low setting
• Dimensions (HxWxD): Approx. 15.2" x 11.4" x 19.7"
• Weight: Approx. 33 lbs
• Refrigerant: R410A

Controls and Settings

Access all functions via the electronic control panel on top of the unit.

Control Panel: POWER button, HUMIDITY UP/DOWN, FAN SPEED (High/Low), TIMER (1-24 hours), FILTER ALERT reset, CONTINUOUS mode.

Display Icons: Power, Bucket Full, Filter Clean, Target Humidity, Fan Speed, Timer, Continuous Mode.

Humidity Setting: Adjust from 35% to 85% RH in 5% increments. Fan Speed: HIGH for maximum moisture removal, LOW for quiet operation. Timer: Set delay start or auto shut-off from 1 to 24 hours. Continuous Mode: Runs continuously until turned off or bucket is full (if hose not used). Filter Alert: Illuminates when filter needs cleaning; press and hold FILTER button for 3 seconds to reset.

Operation Modes

Normal Mode: Unit runs until desired humidity is reached, then cycles on/off to maintain it. Continuous Mode: Runs non-stop regardless of humidity level (use with drain hose). Laundry Mode: Higher fan speed for faster drying in laundry areas. Timer Mode: Automatically turns unit on or off at set times.

1. Press POWER to turn on.
2. Set desired humidity with HUMIDITY buttons.
3. Select fan speed.
4. For continuous operation, press CONTINUOUS button (ensure drain hose is connected).
5. To program timer, press TIMER, then use arrows to set hours, press TIMER again to confirm.

Tip: Close windows and doors in the room for best efficiency.

Maintenance & Cleaning

Unplug unit before any maintenance.

1. Empty water bucket: When FULL light comes on, remove bucket, pour out water, replace securely.
2. Clean air filter: Remove filter every 2 weeks or as needed; rinse with lukewarm water, let dry completely before reinstalling.
3. Clean exterior: Wipe with soft, damp cloth; do not use abrasive cleaners.
4. Clean bucket: Periodically wash with mild detergent to prevent mold/mildew.
5. Check drain hose: Ensure it is clear and free of kinks if using continuous drain.

WARNING! Do not operate without filter. Never pour water into electrical components.

Storage & Winterization

If not using for extended period (e.g., winter):

1. Unplug unit and empty bucket completely.
2. Clean filter and bucket as described above; let all parts dry thoroughly.
3. Coil power cord neatly.
4. Store upright in a cool, dry place. Cover to prevent dust accumulation.

CAUTION! Do not store unit outdoors or in areas subject to freezing temperatures.

Regulatory Information

This appliance complies with FCC Part 15 Subpart B. It may not cause harmful interference and must accept any interference received. Certified to UL standard 474. For your safety and to ensure performance, use only authorized Frigidaire parts. Copyright © Frigidaire. For support, visit www.frigidaire.com or contact 1-800-374-4432.

Troubleshooting

Reset: Unplug unit for 5 minutes to reset electronic controls.

Service: 1-800-374-4432; www.frigidaire.com