Frigidaire FDL60K1 Dehumidifier Manual

The Frigidaire FDL60K1 is a high-capacity 60-pint dehumidifier designed for residential use in medium to large rooms. It features electronic controls with a digital humidistat, automatic restart, continuous drain option, washable air filter, and a full-bucket alert with auto-shutoff. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Electronic control panel, water collection bucket, washable air filter, continuous drain port, casters for mobility.

Installation

Unpack and inspect contents. Place on a level, stable floor.

1. Position the unit: Allow at least 12-18 inches of clearance on all sides for proper airflow.
2. Install the bucket: Slide the water collection bucket into place until it clicks.
3. Check the filter: Ensure the washable air filter is properly installed behind the front grille.
4. Plug into a dedicated 115V AC outlet.

WARNING! Do not use an extension cord. Ensure the outlet is properly grounded.

First-Time Setup

Plug in the dehumidifier; the control panel will illuminate.

1. Set the desired humidity: Press the HUMIDITY button and use +/- to set a level between 35% and 85%.
2. Select fan speed: Press FAN to choose between Normal and Turbo (high) speed.
3. Set the timer (optional): Press TIMER to program automatic start/stop times.
4. For continuous drainage: Connect a standard garden hose (¾") to the drain port at the back.

CAUTION! Operate only at temperatures above 65°F (18°C) to prevent coil freezing.

Specifications

• Model: FDL60K1
• Moisture Removal: 60 pints per day (at 80°F, 60% RH)
• Coverage Area: Up to 1500 sq. ft. in moderate humidity conditions
• Water Tank Capacity: 16 pints (with full-bucket auto shutoff)
• Power Requirements: 115V, 60Hz, 7.0 Amps
• Operating Conditions: 65°F to 90°F (18°C to 32°C)
• Refrigerant: R-410A
• Dimensions (HxWxD): 24.0" x 15.0" x 11.5"
• Weight: 41.0 lbs
• Noise Level: ≤ 55 dB on Normal setting

Controls and Settings

Access all functions via the electronic control panel on top of the unit.

Control Panel: POWER, HUMIDITY (+/-), FAN (Normal/Turbo), TIMER (1-24 hrs), FILTER ALERT (reset), BUCKET FULL (indicator).

Humidity Control: Set target humidity from 35% to 85%. The compressor will cycle on/off to maintain this level. Fan Speed: NORMAL for quiet operation, TURBO for maximum air circulation and faster dehumidification. Timer: Set delay start (1-24 hours) or auto shutoff. Filter Alert: LED illuminates when the air filter needs cleaning (after 250 hours of operation).

Connecting Drain Hose

For continuous operation, use the drain port to connect a hose.

1. Turn off and unplug the dehumidifier.
2. Remove the bucket and locate the drain port on the back.
3. Insert the adapter (included) into the port.
4. Connect a standard ¾" garden hose (not included) to the adapter.
5. Route the hose to a floor drain, sink, or sump pump.
6. Ensure the hose has a downward slope with no kinks.

Tip: When using continuous drain, the bucket full alert and auto-shutoff are disabled.

Operation

Designed for easy, automatic operation.

1. Power On: Press POWER. The unit will start in the last used settings.
2. Bucket Monitoring: The BUCKET FULL light will illuminate when the 16-pint bucket is full. The unit will automatically shut off. Empty the bucket and reinsert to resume.
3. Turbo Mode: Press FAN to select TURBO for faster dehumidification in very damp conditions.
4. Timer: Press TIMER, then use +/- to set hours (1-24) for delayed start or auto-off.
5. Automatic Defrost: In cold conditions, the unit will automatically cycle into defrost mode to prevent coil icing.

WARNING! Always turn off and unplug before moving, emptying the bucket, or performing maintenance.

Maintenance

Regular maintenance ensures optimal performance and longevity.

Clean the Air Filter: Every 2-4 weeks, or when the FILTER alert light is on.

1. Turn off and unplug the unit.
2. Remove the front grille by pulling from the bottom.
3. Take out the foam filter.
4. Vacuum or rinse under lukewarm water. Let air dry completely before reinstalling.
5. Press and hold the FILTER button for 3 seconds to reset the alert.

Clean the Bucket: Monthly, wash with mild detergent and water to prevent mold/mildew. Rinse thoroughly.

Care & Cleaning

Unplug before any cleaning. Wipe the exterior with a soft, damp cloth. Do not use abrasive cleaners or solvents.

CAUTION! Never immerse the unit in water. Do not use the dehumidifier in dusty or greasy environments without frequent filter cleaning.

Regulatory Information

This appliance complies with Part 15 of the FCC Rules. Operation is subject to the condition that it does not cause harmful interference. Copyright © Frigidaire; trademarks of Electrolux Home Products, Inc. For support, visit www.frigidaire.com or contact 1-800-374-4432.

Troubleshooting

Reset: Unplug for 60 seconds, then plug back in to reset the electronic controls.

Service: 1-800-374-4432; www.frigidaire.com