Frigidaire FDF50S1ENG13 Dehumidifier Manual

The Frigidaire FDF50S1ENG13 is a 50-pint dehumidifier designed for residential use, featuring electronic controls, automatic humidity sensing, continuous drain option, washable air filter, auto-restart after power interruption, and energy-efficient operation. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Electronic control panel, Humidity sensor, Water collection bucket, Washable filter, Continuous drain port, Casters for mobility.

Installation

Unpack and inspect contents. Place on level surface.

1. Position unit: Allow at least 12 inches clearance on all sides for airflow.
2. Check filter: Ensure washable filter is properly installed.
3. Install drain hose (optional): Attach to continuous drain port for automatic drainage.
4. Plug into grounded 120V AC outlet.

WARNING! Do not operate in temperatures below 41°F (5°C). Ensure unit is upright before plugging in.

First-Time Setup

Plug in unit; control panel will illuminate.

1. Set humidity level: Press HUMIDITY button to select desired level (35%-85%).
2. Select fan speed: Choose LOW or HIGH for airflow.
3. Set timer (optional): Use TIMER button to program start/stop times.
4. Check bucket: Ensure empty and properly seated.

CAUTION! Handle bucket carefully to avoid spills. Do not tilt unit with full bucket.

Specifications

• Capacity: 50 pints per day (at 60°F, 60% RH).
• Coverage: Up to 1500 sq ft.
• Controls: Electronic touchpad with digital display.
• Humidity Range: 35% to 85% adjustable.
• Fan Speeds: 2 (Low, High).
• Bucket Capacity: 50 pints with full indicator.
• Drain Options: Manual bucket or continuous drain.
• Power Source: 120V AC, 60Hz.
• Operating Temp: 41°F to 95°F (5°C to 35°C).

Controls and Settings

Control Panel: POWER, HUMIDITY, FAN SPEED, TIMER, FILTER CHECK.

Display: Shows current humidity, set point, timer status, filter alert.

Humidity Setting: Press HUMIDITY to cycle through 35%-85% in 5% increments. Fan Speed: Toggle between LOW (quiet) and HIGH (maximum dehumidification). Timer: Set 1-24 hours for automatic on/off. Filter Alert: LED lights when filter needs cleaning. Auto Mode: Unit automatically adjusts fan speed based on humidity level.

Connecting Drainage

For continuous operation without emptying bucket.

1. Turn off and unplug unit.
2. Remove bucket and locate drain port on back.
3. Attach 5/8" ID hose (not included) to port.
4. Route hose to floor drain or suitable outlet.
5. Replace bucket; plug in and restart.

Tip: Ensure hose has downward slope to prevent water backup.

Operation Modes

Multiple modes for different needs.

1. Normal Mode: Set desired humidity; unit runs until reached.
2. Continuous Mode: Set humidity to 35% for maximum moisture removal.
3. Auto Mode: Unit selects fan speed based on current conditions.
4. Timer Mode: Program to run during specific hours.
5. Laundry Mode: High fan speed for drying rooms faster.

WARNING! Do not operate in enclosed closet or cabinet. Ensure proper ventilation.

Maintenance

Regular maintenance ensures optimal performance.

Clean Filter: Every 2-4 weeks; wash with warm water, dry completely. Empty Bucket: When full indicator lights or manually as needed. Clean Exterior: Wipe with damp cloth. End-of-Season: Empty bucket, clean filter, unplug, and store upright in dry place.

Care & Cleaning

Unplug before cleaning. Use mild detergent and soft cloth only.

CAUTION! Do not immerse unit in water. Never use abrasive cleaners or solvents.

Regulatory Information

UL Listed; meets safety standards. Energy Star certified. Copyright © Frigidaire; trademarks of Electrolux Home Products, Inc. For support, visit www.frigidaire.com or contact 1-800-374-4432.

Troubleshooting

Reset: Unplug for 5 minutes, then restart.

Service: 1-800-374-4432; www.frigidaire.com