Frigidaire FDF50S1 - 50 Pint Capacity Dehumidifier Dehumidifier manual

The Frigidaire FDF50S1 is a high-capacity 50-pint dehumidifier designed for residential use. It features an Energy Star certification, adjustable humidity control, continuous drain option, full bucket alert with auto-shutoff, washable filter, caster wheels for mobility, and a digital display with control panel. Ideal for medium to large rooms, basements, and damp areas. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Digital control panel, 50-pint water bucket, Washable air filter, Continuous drain hose port, Caster wheels, Handle, Power cord.

Installation & Placement

Unpack and inspect contents. Place on a level, stable surface.

1. Choose Location: Place in center of room or area with high humidity, away from walls and furniture for optimal airflow.
2. Clear Area: Ensure at least 12-18 inches of clearance on all sides, especially the air intake and exhaust.
3. Check Floor: Surface must be level to ensure proper operation and water collection in bucket.
4. Install Casters: Attach caster wheels to base if not pre-installed.
5. Prepare Drain Option: For continuous drainage, connect standard garden hose (not included) to drain port and route to floor drain or sink.

WARNING! Do not place in an enclosed space or block airflow. Ensure power outlet is easily accessible and rated for 115V.

First-Time Setup

Plug into a grounded 115V outlet; follow initial setup steps.

1. Insert Water Bucket: Ensure bucket is correctly seated and clicks into place.
2. Power On: Press the POWER button. The unit will beep and the display will light up.
3. Set Desired Humidity: Use the UP/DOWN buttons to set your target humidity level (35%-85%). The unit will cycle on/off to maintain this level.
4. Select Fan Speed: Choose between LOW (quiet) and HIGH (Turbo) fan speed.
5. Set Timer (Optional): Use the TIMER button to program automatic start/stop times.
6. Check Filter: Verify the washable filter is clean and properly installed.

CAUTION! Handle the water bucket with care to avoid spills. Do not operate without the filter installed.

Specifications

• Model: FDF50S1
• Dehumidification Capacity: 50 pints per day (at 60°F, 60% RH)
• Energy Star Certified: Yes
• Operating Temperature: 41°F to 95°F (5°C to 35°C)
• Water Bucket Capacity: 50 pints (removable)
• Air Flow: Adjustable, two-speed fan
• Filter: Washable mesh filter
• Power Requirements: 115V, 60Hz, 4.5 Amps
• Dimensions (HxWxD): Approx. 24" x 15" x 12"
• Weight: Approx. 42 lbs
• Refrigerant: R-410A

Controls and Settings

Access all functions via the digital control panel on top of the unit.

Control Panel: POWER, HUMIDITY SET (UP/DOWN), FAN SPEED (LOW/HIGH), TIMER, TURBO, FILTER ALERT RESET.

Display Icons: Current Room Humidity %, Target Humidity Set Point, Fan Speed Icon, Full Bucket Icon, Timer Icon, Filter Alert Icon.

Settings: Target Humidity (35%-85%), Fan Speed (Low/High/Turbo), 24-Hour Timer (programmable in 1-hour increments), Continuous Operation (hold TURBO for 3 seconds).

Operation Modes

Standard, Turbo, and Continuous Drain modes.

1. Standard Mode: Unit runs until target humidity is reached, then cycles off. Fan speed is user-selectable.
2. Turbo Mode: Press TURBO button for maximum moisture removal. Fan runs at highest speed.
3. Continuous Drain Mode: Connect hose to drain port. Unit will run continuously, bypassing the bucket. Ensure hose is routed downhill.
4. Timer Mode: Set unit to turn ON or OFF after a delay of 1-24 hours.

Tip: Use Turbo mode initially in very damp spaces, then switch to Standard mode for maintenance.

Maintenance & Cleaning

Unplug unit before any maintenance.

1. Emptying the Bucket: When FULL light illuminates, pull bucket straight out, carry to sink, and empty. Wipe dry before reinserting.
2. Cleaning the Filter: Remove filter every 2 weeks or when FILTER light is on. Rinse under lukewarm water, let air dry completely before reinstalling. Press FILTER RESET button.
3. Cleaning the Exterior: Wipe cabinet with a soft, damp cloth. Do not use harsh chemicals or abrasives.
4. Cleaning the Bucket: Periodically clean bucket with mild soap and water to prevent mold/mildew. Rinse thoroughly.
5. End-of-Season Care: Before storage, run unit in Fan Only mode (set humidity to lowest setting) for a few hours to dry internal components.

CAUTION! Never immerse unit in water. Do not operate without the filter.

Storage Instructions

Prepare unit for long-term storage if not in use.

1. Unplug the unit from the electrical outlet.
2. Empty and thoroughly dry the water bucket.
3. Clean the air filter and let it dry completely before reinstalling.
4. Coil the power cord and secure it in the storage wrap.
5. Store the unit upright in a cool, dry place. Cover with a cloth or bag to prevent dust accumulation.
6. Do not store on its side or upside down.

WARNING! Ensure unit is completely dry inside to prevent mold growth during storage.

Regulatory Information

This appliance complies with Part 15 of the FCC Rules. Operation is subject to the condition that this device does not cause harmful interference. This product is Energy Star certified by the U.S. EPA. For support, visit www.frigidaire.com or contact Frigidaire Consumer Services at 1-800-374-4432.

Troubleshooting

Reset: Unplug unit for 5 minutes to reset control board.

Service: 1-800-374-4432; www.frigidaire.com